All About the Red Tailed Hawk Grit Red tailed Hawk Calls & Screams (w AUDIO examples) Bird Watching HQ Red tailed Hawk Audubon Field Guide Red tailed hawk Description, Prey, & Facts Britannica Hawk Coloring Pages Young Red Tailed Hawk. Note: RS3 Vehicles will need to modify plug on wear sensor DTC 30 is a controllable torque, multi purpose compound, proven effective in a range of series. It delivers superior release characteristics and smooth pedal feel and initial bite for dirt and circle tracks, NASCAR modified, drag racing, trophy trucks, pro buggies, and more. Features: Consistent, smooth braking Good cold effectiveness All Hawk Performance compounds are not compatible with carbon ceramic rotors. Hawk pads are designed to work with Iron Metal rotors. Medium torque 38C 649C operating temperature range 38C 426C optimal temperature range All Hawk Performance compounds are not compatible with carbon ceramic rotors. Hawk pads are designed to work with Iron Metal rotors. Vehicle Fitment: To ensure correct compatibility we always recommend comparing your existing brake pads to the pad shape diagram provided above. Vehicle fitment provided is to be used as a guide only and may not suit your vehicle. Note: RS3 Vehicles will need to modify plug on wear sensor 2015 2019 Audi RS3 8V 2006 2008 Audi RS4 B7 2012 2018 Audi RS4 B8 2010 2016 Audi RS5 8T 2003 2005 Audi RS6 C5 2007 2015 Audi R8 42 Important Installation and Brake Bedding Procedure: STREET Installation instructions should be followed in accordance with the application? specific brake pad installation instructions provided by the vehicle manufacturer. Brake Pad Installation Procedure: Install brake pads properly. Be sure pads are securely positioned in the caliper. Check Brake Fluid. Flush and replace, as needed. Check all hydraulic parts for excess wear and tear. Check rotor for deep grooves or scoring. Resurface or replace rotor, as needed. If rotors do not need resurfacing, then contamination from the previous brake pads must be removed. Sand rotors with 130? grit sandpaper using moderate pressure. Use soap and water to clean rotor surface after sanding. Rotors should be free and clear of oil, grease and brake fluid. Inspect calipers for freedom of movement. Lubricate where necessary. Street Brake Pad Burnishing Bedding? In Instructions: To break in the new components, make 6 to 10 stops from approximately 30 to 35 MPH applying moderate pressure. Make an additional 2 to 3 hard stops from approximately 40 to 45 MPH. DO NOT DRAG BRAKES! Allow 15 minutes for brake system to cool down. Your brakes are now ready for use and can be driven normally. MOTORSPORTS Installation instructions should be followed in accordance with the application? specific brake pad installation instructions provided by the vehicle manufacturer. Brake Pad Installation Procedure : Install brake pads properly. Be sure pads are securely positioned in the caliper. Check Brake Fluid. Flush and replace, as needed. Check all hydraulic parts for excess wear and tear. Check rotor for deep grooves or scoring. Resurface or replace rotor, as needed. If rotors do not need resurfacing, then contamination from the previous brake pads must be removed. Sand rotors with 130? grit sandpaper using moderate pressure. Use soap and water to clean rotor surface after sanding. Rotors should be free and clear of oil, grease and brake fluid. Inspect calipers for freedom of movement. Lubricate where necessary. Motorsports Brake Pad Burnishing Bedding? In Instructions: After reaching medium speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat four or five times. At higher speeds engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat five times. At or near race speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat three times. Allow a few seconds between brake engagements while car is in motion. Do not hold brake pedal. Park car for approximately 20 minutes or until brake rotors are completely cool to the touch. If during the above steps the brake pedal becomes soft or brake fade is noticed, park the car immediately for approximately 20 minutes. Do not hold brake pedal. IMPORTANT REMINDERS WHEN BURNISHING BEDDING BRAKE PADS: Do not attempt to use badly worn or damaged rotors with new brake pads. Do not drag brakes while car is moving during break? in procedure. Do not engage pedal while car is stopped at any time following the break? in procedure. Upon completing the procedure, allow the brake system to completely cool before racing. Applying the pedal a few times before the start of the race will allow the brake pads to heat up before attempting to reach race speeds. Clean a used rotor surface with fine sand paper or steel wool, rinse with water, dry and install before bedding new pads. Some forms of racing dont allow time for the proper break? in procedure to be performed. However, it is still very important to attempt to perform at least the core of the procedure: Build up heat slowly and allow the system to completely cool down before racing if possible